竞猜篮球网

當前位置:網站首頁 > 新聞中心 > 行業新聞
行業新聞
  • 點焊機維護注意事項
  • 本站編輯:杭州雄盛機械有限公司發布日期:2019-10-18 19:11 瀏覽次數:
  1、點焊機操作人員不得以身體任何部位或任何物件靠近觸摸傳動的齒輪、傳動槽輪、鏈輪、皮帶、鏈條、調直機、感應體、接近開關以及電柜內、變壓器等帶有危險電壓的導體部分。                                                       
 
2、點焊機操作人員不得把手或物體靠近正在加壓運動的上電極或放入上、下電極之間。
 
3、點焊機操作人員不得帶電插或碰掉焊網電源變壓器上的功率調節插把,不得掀起防護板。4、點焊機操作人員不得拆掉、碰斷主機和電控柜上的接零(接地)安全保護線,定期檢查接零(接地)安全保護線是否良好。
 
5、當點焊機電控柜內有熔斷時,應先停機停電,由電工查出熔斷原因之后,再以相同型號規格的熔芯更換,否則將引起火災和燒毀器件。
 
6、點焊機操作人員不得隨意調整電控柜內的器件,不得隨意把工具、鐵絲等雜物放入電控柜或放在機箱頂部以及齒條上。
 
7、點焊機操作人員必須及時對軸承、滑塊、滑道、滑套、鏈輪、鏈條、齒輪、齒條等滾動摩擦的零部件加注潤滑油,不得缺油運轉。加注潤滑油應在停機后進行。必須在運行中加
 
 
注潤滑油的部位,不得以加油器具碰觸運行中的機構,可采用滴注方式。
1. The operator of spot welder shall not touch any part of the body or any object near the transmission gear, transmission groove wheel, sprocket wheel, belt, chain, straightening machine, induction body, proximity switch, electric cabinet, transformer and other conductor parts with dangerous voltage.
 
 
 
2. The operator of spot welder shall not put his hand or object near the upper electrode which is moving under pressure or put it between the upper and lower electrodes.
 
 
 
3. The operator of the spot welder shall not plug or touch the power adjustment plug on the power transformer of the welding mesh, and shall not lift the protection plate. 4. The operator of spot welder shall not remove or break the safety wire connecting zero (ground) on the main machine and electric control cabinet, and regularly check whether the safety wire connecting zero (ground) is in good condition.
 
 
 
5. When there is a fuse break in the mechanical and electrical control cabinet of spot welding, the machine should be shut down and power cut first. After the electrician finds out the cause of the fuse break, the core of the same model and specification should be replaced.
 
 
 
6. The operator of spot welder shall not randomly adjust the components in the electric control cabinet, and shall not randomly put the tools, wire and other sundry objects into the electric control cabinet or on the top of the machine case and rack.
 
 
 
7. The operator of spot welding machine must fill lubricating oil for the rolling friction parts such as bearings, sliders, slideways, sliding sleeves, sprockets, chains, gears and rack in time, and must not run short of oil. Lubricating oil filling shall be carried out after shutdown. Must be added in operation
 
 
 
 
 
The place where lubricating oil is poured shall not be touched by the oiler with the running mechanism, but by drip.
拉菲彩票 拉菲彩票 贵州快3 贵州快3 陕西11选5 甘肃11选5 新疆11选5 新疆11选5